Findmall.com
 
 






Minelab Safari/Quattro Forum


Welcome! Log In Register
Noise Cancel
Posted by: Cos
Date: September 05, 2017 04:46PM
I have used the Minelab Safari for a number of years now, and almost always in the sensitivity auto mode. It is very easy to use the noise cancel in this mode with the detector coil right on the ground (as recommended by Andy Sabisch in his book). Recently I have started to adjust the sensitivity mode in manual, selecting either 16 or 17. With those manual settings I seem to be getting more depth, and more silver dimes in hunted out sites. Using the 11" standard coil, I am now faced with another problem. No matter where I place the 11" coil on the ground to noise cancel with a manual setting of 16 or 17, my screen indicates I have iron under my coil. How does one find a spot to noise cancel when in the manual sensitivity mode? I realize I could turn the sensitivity down, and then back up after the noise cancel, but Andy's books says you must noise cancel whenever you change settings??? Has anyone noticed this problem? How can you find a spot anywhere in a park to do a noise cancel without iron being under your coil?? Supposedly, the noise cancel will not work if you have iron under your coil. Help, and thank you.

avatar
Re: Noise Cancel
Posted by: Champ Ferguson
Date: September 06, 2017 05:35PM
There are simply places that so much metal trash in the ground that you cannot NC with the coil on the ground. When I encounter that, I just NC in the air as ML recommends.

There is a debate on what is best.
A) you NC where you will be swinging the coil (on the ground essentially)- Andy's recommendation
B) where most of the EMI is, ie in the air - manual recommendation

Personally, I don't think it makes much difference in most cases so long as there isn't metal in the soil near the coil.
Theres a good thread on NC by sube in the CTX forum ongoing right now. I highly recommend reading thru it and forming your own opinion on the matter.



Minelab CTX
Minelab Excalibur II
Minelab Safari

avatar
Re: Noise Cancel
Posted by: Goldstrike
Date: September 08, 2017 03:59PM
Sometimes, parks are really full of trash, aluminum cans, pull tabs and iron junk and while you think it's all full of metal junk, there are always spots where there is no junk. It's just a question of finding that spot where there isn't any. I usually crank up the sensitivity and sweep making sure there are no junk signals underneath and proceed to N.C. there. I must admit I have had to N.C. in the air but don't know if it reduces the detectors effectiveness and accuracy?

Re: Noise Cancel
Posted by: Cos
Date: September 19, 2017 01:34PM
Thank you both for your responses and suggestions. However, I still cannot find a place in any park to noise cancel when the detector is set to manual. No matter where I set the coil on the ground in manual, I get iron readings on the screen usually a 9 or some other number. This seems somewhat strange to me, because if I had the sensitivity set to auto I can easily find a place on the ground with no iron indication on the screen. The only way I can noise cancel in manual is to raise the coil 6 inches or so off the ground. I hope by doing this my Safari will select the most appropriate (and deepest) frequencies. If not, I might as well be searching in auto. My hope is that by using manual (16 or above) I would be getting more depth in heavily hunted parks.

Re: Noise Cancel
Posted by: enderman
Date: October 03, 2017 09:04AM
I think the Etrac manual says to noise cancel in the air, don't quote me on that.

I don't think it's critical unless the noise is coming from the ground, I think most of it comes through the air though. You could though keep your coil flat a parallel with the ground.

avatar
Re: Noise Cancel
Posted by: sasquache
Date: October 03, 2017 06:38PM
I seem to always noise cancel in the air if i noise cancel on the ground my Safari is a little erratic at times.I always run manual sensitivity right around 16-17 i hardly ever use auto because the depth is not so good.

Sorry, only registered users may post in this forum.

Click here to login