I have been testing the 1.10 Beta test version, and other than a couple issues that I have personally witnessed and reported to Nokta on the provided email, on the Legend I did the testing with I am really liking this new version 1.10 which will be changed to 1.11 once finalized.
The TIDs (Target IDs for newbies) seem much more stable from previous versions with this Beta Test version 1.10, when the Legend locks on to a target I am not seeing the IDs jumping all over the place, like they were for me in previous versions, also on the ground I detect the GB (Ground Balance) seems to be more stabilized from previous versions, I have two legends one I have not updated just yet but will, so my observations are from running one legend with 1.10 and the other with 1.09 side by side, the tones are another thing I have noticed on the Legend with 1.10 I thought the tones were good in 1.09 but the 1.10 tones sound even better to me, with 1.10 much clearer tones.
one thing I have also noticed is when the coil gets over a target in the 1.10 version the target is almost dead center on the 11 inch coil on the center bar that runs from heel to toe just ahead of the stem (this seems to be the hot spot) on the 11 inch coil, the 11 inch coil when I have located a target and wiggle back from said target seems to be even more sensitive at the front edge of the 11 inch coil then what it was in previous versions, it just seems to be way more sensitive at the edges of the 11 inch coil from previous versions, the depth of the Legend with 1.10 also seems to be even deeper in my ground which is extremely mineralized, the legend with the 1.10 version seems to get through my mineralized ground much much better than previous versions, I am seeing depths that I could not achieve with the previous versions on my legend with the 1.10, and I am not talking small depth changes but 2-5 inches of gained depth in 1.10, my Legend with the 1.10 I can now run my Sensitivity up to around 25-27 where before I could only get it to 15-19 before it would get so noisy that it was UN bearable
One thing I will add is another observation before when my Legend would lock on to a target and give me a TID the TIDs would be bouncing around now they are not with 1.10, also another observation that would happen in previous versions when I would get over a target in one of the SMF modes I would switch to a different SMF mode just to see if there was a variance in TID numbers for a target I would run through all three SMF and all five SF (single Frequencies) in previous versions there would be a slight variance in TID numbers depending on which SMF or single Frequency you were in in, 1.10 I am no longer seeing a variance in TIDs in any Of the SMF or SF frequency modes
Now to my question where should the hot spot on the Legend 11 inch coil be or what is others observations as to where the hot spot is, on the 11 inch coil I have been testing the 6 inch coil also but the six inch when the Legend locks on to a target the hot spot is almost the hole coil because of its size.
The TIDs (Target IDs for newbies) seem much more stable from previous versions with this Beta Test version 1.10, when the Legend locks on to a target I am not seeing the IDs jumping all over the place, like they were for me in previous versions, also on the ground I detect the GB (Ground Balance) seems to be more stabilized from previous versions, I have two legends one I have not updated just yet but will, so my observations are from running one legend with 1.10 and the other with 1.09 side by side, the tones are another thing I have noticed on the Legend with 1.10 I thought the tones were good in 1.09 but the 1.10 tones sound even better to me, with 1.10 much clearer tones.
one thing I have also noticed is when the coil gets over a target in the 1.10 version the target is almost dead center on the 11 inch coil on the center bar that runs from heel to toe just ahead of the stem (this seems to be the hot spot) on the 11 inch coil, the 11 inch coil when I have located a target and wiggle back from said target seems to be even more sensitive at the front edge of the 11 inch coil then what it was in previous versions, it just seems to be way more sensitive at the edges of the 11 inch coil from previous versions, the depth of the Legend with 1.10 also seems to be even deeper in my ground which is extremely mineralized, the legend with the 1.10 version seems to get through my mineralized ground much much better than previous versions, I am seeing depths that I could not achieve with the previous versions on my legend with the 1.10, and I am not talking small depth changes but 2-5 inches of gained depth in 1.10, my Legend with the 1.10 I can now run my Sensitivity up to around 25-27 where before I could only get it to 15-19 before it would get so noisy that it was UN bearable
One thing I will add is another observation before when my Legend would lock on to a target and give me a TID the TIDs would be bouncing around now they are not with 1.10, also another observation that would happen in previous versions when I would get over a target in one of the SMF modes I would switch to a different SMF mode just to see if there was a variance in TID numbers for a target I would run through all three SMF and all five SF (single Frequencies) in previous versions there would be a slight variance in TID numbers depending on which SMF or single Frequency you were in in, 1.10 I am no longer seeing a variance in TIDs in any Of the SMF or SF frequency modes
Now to my question where should the hot spot on the Legend 11 inch coil be or what is others observations as to where the hot spot is, on the 11 inch coil I have been testing the 6 inch coil also but the six inch when the Legend locks on to a target the hot spot is almost the hole coil because of its size.
Last edited:
