Menu
What's new
Find's Treasure Forums

Welcome to Find's Treasure Forums, Guests!

You are viewing this forums as a guest which limits you to read only status.

Only registered members may post stories, questions, classifieds, reply to other posts, contact other members using built in messaging and use many other features found on these forums.

Why not register and join us today? It's free! (We don't share your email addresses with anyone.) We keep email addresses of our users to protect them and others from bad people posting things they shouldn't.

Click here to register!

Need Support Help?

Cannot log in?, click here to have new password emailed to you

Recent content by Jeff In North Georgia

  1. J

    Minelab Metal Arm Cuff for the Explorer series & Etrac

    Jeff In North Georgia submitted a new listing: Minelab Metal Arm Cuff for the Explorer series & Etrac - Minelab Metal Arm Cuff for the Explorer series & Etrac Learn more about this listing...
  2. Minelab Metal Arm Cuff for the Explorer series & Etrac

    Minelab Metal Arm Cuff for the Explorer series & Etrac

    A new unused Herke metal arm cuff for Minelab Explorer s, XS, II and Etrac models. Welded construction. Aluminum with black powder paint coating. Includes SS mounting screw, arm strap and a stick in pad. Free shipping in the US. $35 by PayPal Thanks! Jeff
  3. J

    CTX 3030 screen replacement

    I'll answer a few of these replies here. When I replaced the screen, looks like I managed to tear the ribbon cable from the controller to the face plate. Checked with Minelab for one. ~$135 but they will not sell you electronic parts that need to be replaced, have to send it in for repairs...
  4. J

    CTX 3030 screen replacement

    I watched this before I attempted it this. It was helpful but did not address my issue. Am hoping re-seating the ribbon cables will take care of the issue and it is not a problem with the replacement screen.
  5. J

    CTX 3030 screen replacement

    Had a few vertical lines in my display. Bought an aftermarket replacement and put it in. Everything worked OK except the backlight. Not sure if its a ribbon cable issue where I did not get one seated properly or a problem with the new replacement screen. Will take it apart again and re-check...
  6. J

    high ohm speakers

    I sent you a PM.
  7. J

    Gray Ghost Amphibian Headphone Wiring

    Bought a used set and want to convert them to my CTX. Have 4 wires instead of three, all covered with hot melt inside so can't see what wires go to where? Checked them with a meter. White & green have 0 ohms. White or green to the black wire is 5K ohms. White or green to the red wire is...
  8. J

    Minelab Equinox 600 & 800 headphone connector

    THIS ITEM IS NOT MADE OR APPROVED BY MINELAB. This is something I have made and is not commonly available. I have 5 pieces of these for sale. Up for sale is a headphone connector for use with the Minelab Equinox 600 & 800. Could be used to make a headphone adapter / extension cables. Or...
  9. J

    FS: Minelab Red & Blue Detector Bag with Cap

    A new red & blue Minelab detector bag. Also a new Minelab ball cap. $25 shipped in the US. PayPal gift.
  10. J

    Anyone have the pinout for the coil connector on a Minelab CTX 3030?

    Anyone have the pinout for the coil connector on a Minelab CTX 3030? Thanks! Jeff
  11. J

    Repurposing Blue Excal Headphones

    Picked up a used set of Minelab blue Excal headphones that I would like to use on my CTX 3030. But.... These have six wires (five and a shield). Can anyone tell me what each one is? Thanks! Jeff
  12. J

    Minelab CTX water headphone pinout

    Does anyone have the pinout for a Minelab CTX 3030 water headphone connector? Thanks! Jeff
  13. J

    WTB: Etrac for a modification project

    Looking for an Etrac in good working condition. Don't need or want the: coil lower shaft upper shaft plastic arm cuff metal stand batteries or charger Just need the well working control head with battery box / handle. Let me know what you have and what you would like for it? Thanks! Jeff
  14. J

    Think I Got A Good One Yesterday

    Was coin hunting yesterday around an old home site today and got a good one I think? Scratched the back side with the shovel as I was digging it , it was ~8" deep. A plain tongue portion of a two piece buckle. Searched the area well but no sign of the other half. Let me know if you think it...
  15. J

    FS: Classic (0ld) Whites Metal Detector Metal Arm Cuff Extension

    This is a used Jimmy Sierra product. A bolt-on arm rest extension for use with most older White's models. It works with models that used a 3/4" wide X 3/16" thick aluminum, sloped angle bracket for the wrist grip handle. The original blue plastic arm cuff broke and it has been replaced by a...
See more
Top